iGrow800 Training
iGrow 800 - Curtain Programming Tutorial
Curtains requires 2 consecutive output channels.(1&2, 3&4, 5&6, 7&8). The first channel (odd numbered) must be wired to Uncover/Open Curtain, and the other (even numbered) to Cover/Close Curtain. Click the link below for additional information on ...
iGrow 800 - Relative Humidity Staging & Advance Settings Tutorial
With the iGrow 800, you can control Relative Humidity within your Greenhouse Environment. Note: Relative Humidity staging overrides Temperature staging. Here is a video link that guides you through the control process. To get to your Humidity staging ...
iGrow 800 - Staging Equipment - for Temp & Humidity
With The iGrow 800, you can Assign Temperature and Relative Humidity Stages for your equipment to control your environment. Click below for a tutorial on staging iGrow 100 equipment for temperature and humidity. There are 9 temperature stages and 4 ...
iGrow 800 - Programming an Alarm Tutorial
With the iGrow 800 Controller, any one of the available 8 channels can be selected to be an alarm output. Click the link below for information on programming an alarm for an iGrow 800 controller. Set Temperature: lets you select the temp threshold ...
iGrow 800 - Vent Equipment Setup Tutorial
Vents requires 2 consecutive output channels (1&2, 3&4, 5&6, 7&8). The first channel (odd numbered) must be wired to Open vent, and the other (even numbered) to CLOSE it. Click the below for a tutorial on vent setup for the iGrow 100 series. On ...
iGrow 800 - Equipment Setup Overview Tutorial
The iGrow 800 allows user to setup the equipment on the various channels, set their type, assign names, energy type, etc. For each of the outputs, the equipment’s name is displayed, as well as the current controlled state that it is in: AUTO – ...
iGrow 800 - Sensor Setup Tutorial
Please view the following video and necessary steps in setting up your sensors
iGrow 800 - Setting Up An Equipment Override Turtorial
With the iGrow 800 you can set a Timed override that will switch ON or OFF the corresponding equipment during the specified time set by user, you can have it set either to daily reoccurring or one time. Here is a video link to get an understanding of ...
iGrow 800 - Saving & Restoring Configurations
The Save and Restore option lets you label and store your program in either the internal memory of the iGrow 100 Series controller or a USB drive (jump drive). You may have programs for different crops or for different seasons of the year. This will ...
iGrow 800 - Reports Tutorial
The second main section of the iGrow 800 controller is the Reports section. Click below on how to set and read reports for the iGrow 800 Controller.. The Report section provides a brief overview of the options available. This section gives the ...
iGrow 800 - Series Setpoint Tutorial
With the iGrow 800 you can program Temperature, Relative Humidity, and C02 Setpoints . Please view the following video and necessary steps in setting up your sensors Cool Setpoint - if the temperature goes above this threshold it will enter into the ...
iGrow 800 - Hands on Training
This will give you a quick overview of the fundamental aspects of the iGrow 800 Controller. Click below for a training session on the iGrow 800.
iGrow 800 - Programming C02
With the iGrow 800, you can control C02 levels within your Greenhouse Environment You would need your firmware updated to at least 1.0.2.1, and a Digital Integrated Sensor Module Installed on the controller. Here is a video link for the iGrow 800 ...
iGrow 800 - Installing the 4 Output Expansion Board
With the iGrow 800 Controller, you can add additional Expansion Boards for additional outputs control. You can have your expansions Integrated at Factory or you can add the as needed Here is a video on the iGrow 800 Installing the 4 Output Expansion ...
iGrow 800 - Checking Firmware Version
To check the version of the controller please do the following: OK-> 3. System Setup-> 10. Advance->unit info (Button #4) Your Controller may be an iGrow800 M which is for Link Conn 100 Software use. Or it may be iGrow800 C which it used for iGrow ...
iGrow 800 - Integrated Panel Overview
The iGrow 800 Integrated Contactor Panel is a UL approved greenhouse contactor panel and an iGrow 800 controller, conveniently pre-mounted on the door for ease of installation. There's no need to mount two separate boxes with conduits in between. ...
iGrow 800 - Programming Expansion Outputs
Once you have your expansion Board Hardware installed, your equipment operating successfully from toggle switches and your Dip switches addressing set on expansion board accordingly, it’s time to program the software portion of expansion boards. Here ...
iGrow 800 - Setting Up Password Protection
With the iGrow 800 the PASSWORD Feature is used to set password for the use of controller. Here is a video link on iGrow 800 Setting Up Password Protection To get to the Password setup screen, from the home screen you would hit OK->System ...
iGrow800 - Saving History and USB Logging
With the iGrow 800 Controller, you can save Log Files, and setup USB Logging Here is a video on the iGrow800 Saving History and USB Logging Currently supported Save Log File options include: Save History Log File Save Event Log Files USB Logging ...
iGrow 800 - Location Setup for Sunrise and Sunset options
The iGrow 800 has an internal astronomical clock, and the Location Setup feature allows the user to setup the latitude and longitude values and can calculate the precise sunrise and sunset times once the location of the unit is entered. To obtain the ...