iGrow 800 - Reports Tutorial

iGrow 800 - Reports Tutorial

The second main section of the iGrow 800 controller is the Reports section.  

Click below on how to set and read reports for the iGrow 800 Controller..


The Report section provides a brief overview of the options available.  This section gives the reports and graphs of energy and equipment usage as well as operational costs. User can go to reports submenu by pressing OK

Reports_1.png

There are 7 subsections under Reports:
1. Return on Investment
2. Graphing
3. Equipment Costs
4. Energy Costs
5. Equipment Usage
6. Energy Usage
7. Event Logs
To highlight the sub options Wheel or Buttons #1 - #7 can be used to go to the corresponding options. Pressing OK will let user select the options

Reports_2.png

Return on Investment:  allows you to review the return on investment.
Buttton #1 can be used to access this option.

Graphing:  allows you to view graphs for different variables against time. Pressing Button #2 from Repots submenu will take the user to graphing submenu.

Temperature:  allows you to view graphs for the following
• Inside Temperature
• Outside Temperature
• Heat Setpoint
• Cool Setpoint

Humidity:  allows you to view graphs for the following
• Inside Humidity
• Outside Humidity
• Dehumdify Setpoint

Light / Wind / Rain: allows you to view graphs for the following time periods
• Since Reset
• Last Hour
• Last 24 hour
• Last week
• Last 7 days

Stages:  Allows you to view graphs for the following
• Temperature Stage
• Humidity Stage

Relay Outputs:  In the relay option user can view graphs for Relay 1 output to Relay 8 output.

Equipment Status:  In the equipment status option user can view graphs for Channel 1 to
Channel 8.

Equipment Costs and Energy Costs:  Allows you to review the operational cost of the climate zone broken down by equipment, expressed in percentages.

The equipment cost for the following
time periods can be seen:
• Since Reset
• Last Hour
• Last 24 hour
• Last week
• Last 7 days
• Last 30 days
• This Month
• This year

Equipment Usage:  Is where you can review the various equipment runtimes After selecting a given channel/equipment you can select time period to view the usage.  When selecting the equipment usage menu the channels/equipment are listed.

Energy Usage:  In this section you can check the usage of individual energy types.

Electricity, Gas, Oil, Water, or Other.

Event Logs:  The event log options allows you to view the history of various events which happened over a period of time like stage changes, sensor error, relay status changes, etc.
The following time periods are available
• Since Reset
• Last hour
• Last 24 Hours
• Last 7 days
• Last 30 days
• This month
• This year

    • Related Articles

    • iGrow 1400 Save and Restore with LinkConn Software Tutorial

      Click the link below for a tutorial on saving and restoring your iGrow 1400 system using the LinkConn software.

    • iGrow 800 - Vent Equipment Setup Tutorial

      Vents requires 2 consecutive output channels (1&2, 3&4, 5&6, 7&8). The first channel (odd numbered) must be wired to Open vent, and the other (even numbered) to CLOSE it. Click the below for a tutorial on vent setup for the iGrow 100 series. On ...

    • iGrow 800 - Sensor Setup Tutorial

      Please view the following video and necessary steps in setting up your sensors

    • iGrow 800 - Series Setpoint Tutorial

      With the iGrow 800 you can program Temperature, Relative Humidity, and C02 Setpoints . Please view the following video and necessary steps in setting up your sensors Cool Setpoint - if the temperature goes above this threshold it will enter into the ...

    • iGrow 800 - Curtain Programming Tutorial

      Curtains requires 2 consecutive output channels.(1&2, 3&4, 5&6, 7&8). The first channel (odd numbered) must be wired to Uncover/Open Curtain, and the other (even numbered) to Cover/Close Curtain. Click the link below for additional information on ...